Atsparumas UV spinduliams.
Atsparumas UV spinduliams.
Material: 40% Polyethylene HD + 60% Wood fibre
Expansion: 0.0389 mm/m/°C
Sizes: 22.5 x 138 x 3600 mm
Density: 1170 kg/m3
Thermal conductivity: 0.2W/mK
Fasteners: Cobra Hybrid 8-18 stainless steel clip
Elasticity modulus: 3100 Mpa
Elasticity modulus: Delta E = 1,09 < 5
Extrusion type: coextrusion 360°
BROOKLYN co-extruded boards require very little maintenance. Stains such as grease, wine or ketchup can be cleaned easily using soapy water.
It is recommended to wash your deck using a pressure washer (120 bar maximum) at least once a year to remove any moss, which tends to accumulate in the winter and in parts not exposed to the sun.
Washing tougher stains may be done with white spirit without risk of fading.
A fine layer of polyethylene covering the entire board efficiently protects the composite wood against water and any moisture pick-up. Expansions recorded are very low, with only 1 mm per linear meter when exposed to a 30° temperature variation.
The board is completely rain-proof, and rain flows off without letting water penetrate the protected composite wood. UV-resistant additives are also added to this thin layer to avoid any fading over time.
Fiberdeck guarantees that for a 15-year period under normal and correct service conditions, and under installation conditions in compliance with instructions written by Fiberdeck, BROOKLYN boards will not be subject to any defect related to their manufacturing, cracks, splinters, delamination, rotting or structural damage caused by fungi, wood-eating insect or termite attacks.
Fiberdeck guarantees the resistance of BROOKLYN deck boards to stains and fading, subject to compliance with instructions for installation and use in residential applications.
BROOKLYN deck boards are fully resistant to stains, and their radiance is sustained by a co-extrusion process, which covers the board with a pure polyethylene film to ensure perfect sealing of the coating. Maintenance is easier and is limited to simple water rinsing.
The high-density polyethylene and wood fibre mixture composing the core of the board also ensures very good resistance to impacts and wear.
BROOKLYN boards must be implemented in compliance with the installation notice using Cobra Hybrid 8-18 stainless steel clips. A bag of 90 clips fastens about 5 m2of boards.
These new dual-material clips help hold the stainless steel screws in place during installation. The time saved during installation is considerable. Moreover, the universal stainless steel screws are self-drilling in softwoods and exotic woods, and aluminium joists.
Boards fastened using Cobra Hybrid 8-18 clips can be easily removed without disassembling the entire deck.
Joist gaps (centre-to-centre distance) are at most 40 cm for BROOKLYN boards. It is recommended to apply a joist barrier on softwood joists to extend their durability.
BROOKLYN composite deck boards are eco-friendly products. 95% manufactured with raw materials from the recycling industry, the boards are also entirely recyclable.
High-density polyethylene (HDPE) comes from the recycling of plastic waste (plastic bottles), and the wood fibres come from sawdust from manufacturers such as furniture makers.
The manufacture of Brooklyn composite deck boards does not harm tropical forests; it is an interesting alternative to exotic woods.
A range of screw-in boards, identical to Brooklyn boards, 22.5 x 138 mm section, but without grooves on the sides, may be used to create sundecks for swimming pools, stairs, floor openings and also a finishing strip around the deck.
Stainless steel Cobra WPC screws, 5 x 63 mm, which resist rust and are offered in the same colour as the boards for more discretion, are used to fasten skirting and finishing boards.
Finally, it is always possible to use an aluminium angle bar to ensure the peripheral contour of the deck and mask the junction between two grooved boards.
A range of 10 x 84 mm skirting boards, grooved on one side and smooth on the other, offered in four colours, complete the Brooklyn board range, making it possible to create deck contours at a height of about 10 cm.